Husqvarna 1130ST Скачать руководство пользователя | Manualshive

Страница: 25 / 32

background image

25

KEY PART
NO. NO.

DESCRIPTION

   1   532 18 41-10   Lever, Auger Control, RH
   2   532 18 41-09   Lever, Traction Drive Control, LH
   3   532 17 94-39   Nut, Cage 1/4-20
   4   532 17 88-88   Bushing, Flange
   5   532 16 96-75   Retainer, Hairpin
   6   532 18 04-02   Screw, Hex Head 1/4-20 x 3/4
   7   532 17 86-52   Rod, Interlock
   8   532 18 40-03   Tube Assembly, Interlock, RH
   9   532 17 86-51   Tube Assembly, Interlock, LH

10   532 18 41-06   Panel, Control
11   874 78 05-24   Screw, Hex Head 5/16-18 x 1-1/2
12   874 78 05-28   Screw, Hex Head 5/16-18 x 1-3/4
13   532 18 41-07   Handle Tube, LH
14   532 18 41-08   Handle Tube, RH
15   873 80 05-00   Nut, Lock 5/16-18
16   819 13 13-16   Washer, Flat 3/8
17   532 17 88-99   Knob, Handle
18   532 17 90-93   Rod, Auger Control
19   532 17 90-98   Rod, Traction Control
20   532 18 04-28   End, Control Rod
21   873 35 05-00   Nut, Hex, Jam 5/16-18
22   872 12 06-18   Bolt, Carriage 3/8-16 x 2-1/4
23   532 18 40-88   Handle Tube, Lower
24   532 18 04-47   Sleeve, Spring
25   532 18 09-26   Spring, Traction Drive
26   532 17 86-69   Spring, Auger Control
27   871 21 06-16   Screw, Hex Head 3/8-16 x 1
28   532 18 04-94   Clip, Panel
30   532 18 29-06   Console, Panel
31   532 17 52-62   Screw, Hex Head, Tapping #10-24 x 1-1/4
32   532 18 44-71   Screw, Hex Head, Tapping #10-24 x 1/2
33   532 18 41-11   Latch, Interlock
34   532 18 35-18   Bolt, Shoulder
35   532 06 80-38   Nut, Lock 1/4-20
36   532 17 88-31   Spring, Torsion
37   532 17 86-58   Spring, Interlock
38   532 17 86-66   Headlight, Halogen
39   532 17 86-68   Bezel, Headlight
40   532 18 09-64   Harness, Headlight (Halogen)

NOTE:

All component dimensions given in U.S. inches

1 inch = 25.4 mm

REPAIR PARTS

HANDLES

SNOW THROWER - - MODEL NO. 1130ST (HU1130STB), PRODUCT NO. 954 22 30-81

«
...
23
24
25
26
27
...
»

Содержание 1130ST

































Отзывы:

Нет отзывов

Похожие инструкции для 1130ST

Бренд: Gardner Denver Страницы: 45

Бренд: Yard force Страницы: 3

Бренд: Land Pride Страницы: 48

Бренд: Oleo-Mac Страницы: 32

Craftsman 944.529821

Бренд: Sears Страницы: 52

Бренд: Ryobi Страницы: 12

4SISON BLB4QL-M

Бренд: Sabre Страницы: 48

Бренд: Intec Страницы: 60

Groundsmaster 4000-D

Бренд: Toro Страницы: 64

Бренд: Meyer Страницы: 2

Бренд: Benchmark Страницы: 26

Бренд: Elektror Страницы: 52

Бренд: GreenWorks Pro Страницы: 14

Бренд: RCm Страницы: 132

Бренд: FIORENTINI Страницы: 16

Бренд: Tomahawk Страницы: 31

Бренд: Vortice Страницы: 108

Бренд: Toro Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды