Husky HU80833, Руководство оператора

Страница: 15 / 33

10 — English
OPERATiON

Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:

Push up on the lock out until it clicks into the slot.
To disengage the lock out:

Push the lock out down and into its original position.
For the most effective cleaning, the spray nozzle should be
between 8 in. and 24 in. from the surface to be cleaned. If
the spray is too close it can damage the cleaning surface.
SELECTiNg ThE RighT QUiCK-CONNECT
NOzzLE FOR ThE JOB
See Figure 21.
Before starting any cleaning job, determine the best nozzle
for the job. Each of the nozzles has a different spray
pattern. The nozzle patterns are: 25° (for general purpose
or large surfaces), 15° (for tough jobs), 0° (for spot cleaning
or hard-to-reach areas), and the Soap Blaster
™
nozzle (for
long and short range detergent application).
 WARNING:
NEVER change nozzles without locking the lock out on
the trigger handle and NEVER point the wand at your
face or at others. The quick-connect feature contains
small springs that could eject the nozzle with some force.
Failure to heed this may cause personal injury.
Using the quick-connect collar, changing nozzles is easy.

Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
To connect a nozzle to the trigger handle:

Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.

Push the nozzle into the quick-connect collar until it clicks
in place and is secured properly.
To disconnect a nozzle from the trigger handle once the
cleaning job is complete:

Turn off the pressure washer and shut off the water
supply. Point nozzle in a safe direction and pull trigger to
release water pressure.

Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.

Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in the
nozzle holder for storage.
wAShiNg wiTh DETERgENT
See Figures 22 - 23.
NOTE:
When using detergent, the coiled high pressure
hose can be relocated to the hook-and-loop strap located
behind the handle bar instead of the strap located on the
carrying handle.
Use only detergents designed for pressure washers; house-
hold detergents, acids, alkalines, bleaches, solvents, flam-
mable material, or industrial grade solutions can damage
the pump. Many detergents may require mixing prior to use.
Prepare cleaning solution as instructed on the solution bottle.
 Place the injection hose in the bottom of the detergent
bottle/container.

Install the Soap Blaster™ nozzle on the spray wand.
 Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
For long range detergent application:
With the Soap Blaster™ nozzle installed on the spray wand and
the engine shut off, pull nozzle up until it clicks into place.
For short range detergent application:
With the Soap Blaster™ nozzle installed on the spray wand
and the engine turned off, push the Soap Blaster™ nozzle
down as far as it will go.
Before shutting off the engine:

Place the injection hose in a bucket of clean water.
 Flush for 1 - 2 minutes (spray clear water through the
spray wand).

Shut off the engine.
NOTE:
Shutting
OFF ( O )
the engine will not relieve pressure
in the system. Point nozzle in a safe direction and pull trigger
to release water pressure.
RiNSiNg wiTh ThE PRESSURE wAShER

Turn off the pressure washer and shut off the water
supply. Point nozzle in a safe direction and pull trigger to
release water pressure.

Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.

Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in the
nozzle storage area on the top of the machine.

Select the right nozzle for the job:
• Use medium pressure nozzle (green) for items such as
a car or boat.
• Use higher pressure nozzle for jobs such as stripping
paint and degreasing the driveway. When using these
nozzles, test a small area first to avoid surface damage.

Start at the top of the area to be rinsed and work down,
overlapping the strokes.
USiNg ThE CLEANiNg DECK
See Figures 24 - 25.

Install the cleaning deck and connect the garden hoses
as described in the assembly section of this manual.

Start the pressure washer as described earlier in this
manual.

Walk slowly behind the cleaning deck, cleaning as you
go.
NOTE: If striping or swirling occurs, slow your pace.
If problem continues, see
Troubleshooting
later in this
manual.