HunterLab UltraScan PRO Скачать руководство пользователя страница 2

Страница: 2 / 55

UltraScan PRO Supplemental Manual for EasyMatch QC Ver. 2.0

Copyrights and Trademarks

This documentation contains proprietary information of Hunter Associates Laboratory, Inc. Its
reproduction, in whole or in part, without express written consent of Hunter Associates Laboratory,
Inc. is prohibited.

EasyMatch and UltraScan are registered trademarks for Hunter Associates Laboratory, Inc.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

Duraflect, Spectraflect, and Spectralon are trademarks of Labsphere, Inc.

Teflon is a registered trademark of Dupont.

Caution: If the equipment is used in a manner not specified by HunterLab, the overall

safety may be impaired. This instrument is for indoor use only and not suitable for a

wet location

Caution: There is a potential of a UV Light hazard in using this instrument. Please

avoid looking directly at the light.

Содержание UltraScan PRO
























































Результаты поиска

Содержание UltraScan PRO

Отзывы:

Похожие инструкции для UltraScan PRO

Бренды по названию

Популярные бренды

HunterLab UltraScan PRO, Дополнительное руководство

Результаты поиска

Содержание UltraScan PRO

Отзывы:

Похожие инструкции для UltraScan PRO

Бренды по названию

Популярные бренды