HunterLab UltraScan PRO Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 55

background image

UltraScan PRO Supplemental Manual for EasyMatch QC Ver. 2.0

45

3.

There is a mark on the optional cell holders, place the cell so the mark is on the same side as
the mark on the vertical wall.

Figure 60. Cell Holder Installed

4.

When installed correctly the cuvette is centered in the transmission compartment.

Cell Holder, Small Volume Cell for Transmittance (D02-1011-886) & Small Volume Cell with
Two Screw Caps & A13-1011-613)

This option provides a holder for a cylindrical, small volume transmittance cell. Each cell is shipped
with two caps, one that is solid and screws on, and one that is threaded and covered with injectable
Teflon

™

. The cell and holder together are used for total transmittance measurements of small

quantities of liquids.

Figure 61. Small Volume Transmittance Cell & Holder

«
...
43
44
45
46
47
...
»

Содержание UltraScan PRO
























































Отзывы:

Нет отзывов

Похожие инструкции для UltraScan PRO

Workstation Monitor 724

Бренд: 3M Страницы: 21

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 24

Бренд: 3M Страницы: 2

SoundPro SE Series

Бренд: 3M Страницы: 293

Бренд: Kane Страницы: 16

Бренд: Bacharach Страницы: 48

Бренд: Bacharach Страницы: 24

Бренд: Macnaught Страницы: 14

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

Бренд: PCE Instruments Страницы: 6

Бренд: Omega Страницы: 13

Amplitude T Series

Бренд: OTOVATION Страницы: 15

Бренд: TDI Страницы: 32

Бренд: Kapro Страницы: 60

Бренд: ATI Technologies Страницы: 4

Бренд: Simpson Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды