Hunter SRC Plus Скачать руководство пользователя страница 27

Страница: 27 / 36

Fig. 1

��

�� 

SRR Remote Control

Smart Port

Wiring Harness

Preparing the Communication Port

To utilize the SRR Remote Control

System, your Hunter controller must be

equipped with the SRR SmartPort

wiring

harness. This wiring harness provides

the communication port where the SRR

receiver is attached. The SmartPort

installation instructions are included in the

SRC

Plus

installation and programming

instructions. Additional wiring harnesses

can be purchased separately to allow you

to utilize the transmitter and receiver with

additional controllers.

Installing the SRR Remote

Wiring Harness

1. Install a 1⁄2" female threaded “Tee” in

the field wiring conduit approximately

12" below the SRC controller. (Note:

the harness may be installed out doors

by first bringing the conduit through

an exterior wall, then installing the

appropriate fitting).

2. Feed the red, white and blue wires of

the harness through the base of the

“Tee” and into the controller wiring

compartment as shown in Figure 1.

3. Screw the harness housing into the

“Tee” (or other fitting) as shown in

Figure 1.

4. Attach the red, white and blue wires

from the harness to the terminal block

of the controller as shown in Figure 2.

�� 

�

��

�

��

�

�� 

Fig. 2

Extending the Wiring Harness

Any extension of the wiring on the

harness

may

result in an error message

in the controller display and possible

malfunction of the remote unit due to

radio interference. In some situations,

lengthening of the harness may work

fine, in others it may not work at all (it

is site specific). In either case, extending

the wiring harness should be done using

shielded cable to minimize the possible

effects of electrical noise. Hunter

’

s SCWH

is a wiring harness with 25 feet of shielded

cable which makes extending the receiver

connection fast and simple.

Transmitter

Preparing the Transmitter for Use

Your SRR System is designed to work

right out of the box. This means that

other than installing the battery, you

may chose to skip this entire section.

However, we recommend you read it

because with a few simple steps you can

customize your SRR to add functionality

and security to your system. Be aware that

if you change your transmitter address or

maximum station number as described

Assembled

INSTALLATION AND PROGRAMMING

Pre-assembled

1⁄2

" Thread

To Controller

Содержание SRC Plus





































Результаты поиска

Содержание SRC Plus

Отзывы:

Hunter SRC Plus, Руководство по эксплуатации товара, Страница: 27 / 36

Результаты поиска

Содержание SRC Plus

Отзывы: