Hunter SRC Plus Скачать руководство пользователя страница 15

Страница: 15 / 36

�� 

�

� �

�

��

15' Minimum (4.5 m)

PSR Series

Pump Start Relay

To Pump

Plus

To prevent pump damage,

connect a jumper wire from

any unused station terminal

to a station terminal with a

control valve installed. If

there is a power failure and

the back up battery fails, a

default program will operate

all stations for 10 minutes.

Unused stations will still

attempt to operate the pump,

potentially causing damage

to the pump. If connected to

an operational valve, the

result would be an over

watered station instead of a

damaged pump.

Connecting a Pump Start Relay

NOTE:

Complete this section

only if you have a pump start

relay installed. A pump start

relay is an electronic device

that uses a current from the

controller to actuate a separate

electrical circuit to energize

a pump to provide water to

your system.

The controller should be mounted at least

15 feet (4.5m) away from both the pump

start relay and the pump. When a pump

start relay comes on it sends out surges

that may potentially cause damage to a

controller that is mounted to close. When

a pump is to be operated by the controller,

a pump start relay must be used. Hunter

offers a full range of pump start relays for

most applications.
1. Route a wire pair from the pump relay

into the controller housing.

2. Connect common wire to the screw

slot C (Common) and the remaining

wire from the pump relay to the MV

screw slot.

Relay current draw must not exceed

.35 Amps.

Do not connect controller

directly to pump – damage to controller

can result.

NOTE:

If a rain sensor is

installed with your SRC

along with a pump start relay,

the relay common must be

connected to the RS terminal.

SRC

Plus

Controller

Содержание SRC Plus





































Результаты поиска

Содержание SRC Plus

Отзывы:

Hunter SRC Plus, Руководство по эксплуатации товара, Страница: 15 / 36

Результаты поиска

Содержание SRC Plus

Отзывы: