background image

2

Hunter Fan Company 

41878-01 • 05/18/04

3

41878-01 • 05/18/04 

Hunter Fan Company

Mounting and Optional Accessories

Understanding Mounting

Hunter’s patented mounting system provides you maximum 
installation fl exibility and ease. You can install your Hunter fan in one 
of two ways, depending on ceiling height and your preference: Standard 
or Angle mounting.  e steps in this manual include instructions for 
both mounting methods.

Considering Optional Accessories

Consider using Hunter’s optional accessories, including a wall-mounted 
or remote speed control. To install and use the accessories, follow 
the instructions included with each product. For quiet and optimum 
performance of your Hunter fan, use only Hunter speed controls.

Standard Mounting

 hangs from the 

ceiling by a downrod (included). Use the 
2.5 inch downrod for ceilings 8-9 feet 
high. Use the 8 inch downrod for ceilings 
higher than 9 feet. 

Angle Mounting

 recommended for a 

vaulted or angled ceiling

All Hunter fans use sturdy 3/4” 
diameter pipe to assure stability and 
wobble-free performance. 

You must hang this fan from an 8 feet or higher 
ceiling. Use the 2.5 inch downrod for ceilings 
between 8 feet and 9 feet high. Use the 8 inch 
downrod for ceilings higher than 9 feet. 

 is fan cannot be hung on ceilings lower than 8 feet.

Содержание Gallery Edotion
















Отзывы: