background image

CARE

19

Removing the Vanes (If Necessary)

 

Push up on the vane.

 

Gently open the vane hook by inserting a credit card-sized piece of rigid plastic between the 
vane and the long prong of the vane hook.

 

Carefully remove the vane.

Cleaning Procedures

All Fabrics 

Dusting

 

Regular light dusting with a feather duster is all the cleaning that is needed in most 
circumstances.

Vacuuming

 

Use a hand-held vacuum with low suction for more thorough dust removal. 

Spot-Cleaning

 

Prepare a solution of warm water and a mild detergent. 

 

Dampen a clean cloth in the solution and wring it out.

 

Dab the spot with the dampened cloth until it is gone.

Caution:  

Vertical fabrics should not be spot-cleaned or immersed in water.

Compressed Air

 

You can use compressed air or a hair dryer (cool setting) to blow the dust off your valance 
or to clean aluminum or vinyl components.

Vertical Fabric Only

Ultrasonic Cleaning

Ultrasonic cleaning for vertical fabrics should be perform only by a professional.

 

Specify that a mild detergent solution be used.

important: 

Never immerse the headrail into the solution.

Injection/Extraction Cleaning

 

This type of cleaning injects a cleaning solution into the fabric and immediately extracts the 
dirty solution.

Содержание Specialty Motorized Vertical Blinds

























Отзывы: