manualshive.com logo in svg

HULTDINS SuperSaw 651S, Руководство по установке

Поделиться
Скачать
HULTDINS SuperSaw 651S Скачать руководство пользователя страница 25

I N I T I A L   U PS TA R T

en011106b_ss651.FM

SuperSaw 651S

25

Adjusting chain tension pressure

1.

Lower the grapple saw to the ground and shut off the 
engine.

2.

Connect a suitable pressure gauge to the pressure test 
point (1) using the hose P/N 0724042

Note! 

Place the pressure gauge so that the pressure 

easily can be checked from the operator’s cabin.

Important!

Never adjust any hydraulic pressures without using a 
pressure gauge.

3.

Start the engine and read the chain tension pressure 
when the saw function is activated.

4.

Adjust the chain tension pressure on the pressure 
regulating valve (2).

•

Increase the pressure by tightening the set 
screw.

•

Decrease the pressure by loosening the set 
screw.

For a proper pressure range, refer to Technical Data.

ill. 24

Adjusting chain tension pressure

1

Pressure test point

2

Pressure regulating valve

1

2

Содержание SuperSaw 651S



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды