3. Assembly of the rebound target
Take hold of the tubes 10 and 3 and connect these through the draw cord at the
lower end of the rebound target. Bolt the ends of the rods 10 on the ground, to-
gether with the goal frame. Fasten the top side and the sides of the rebound
target with the bungee loops on the goal frame. Pay attention that the clips are
on the back side so that they cannot be hit by the ball. Now fix the frame covers
with the sewn-in hook and loop fasteners on to the goal frames. You can adjust
the inclination of the rebound target wall by loosening the tube connection clip on
the tube no. 12 and 13, adjusting the desired angle and closing again the clip (see
fig. 3)
4. Stand locking of the goal
Finally fix the goal frame by means of the pegs in the ground. Ascertain that the
ground is suitable for the application of pegs (e.g. no water pipes for sprinkler
devices!). Make sure that the pegs are completely driven into the ground and
have a firm position. Avoid protruding fastenings (risk of stumbling). On too hard
grounds the goal must be secured by appropriate measures in another way
against falling over in order to prevent risk of injuries. Never play with an unse-
cured goal and never leave the goal unsecured.
USAGE INSTRUCTIONS
• Only set up the goal on level ground.
• Please keep a minimum distance of at least 3 m to any surrounding obstacles.
• Secure the goal to keep it from toppling over – even if not in use.
• Avoid exposing the product unnecessarily to bad weather conditions. Keep it in
a cool and dry storage area.
• Check for any rust on the product and remove it immediately. Pushing together
the metal parts could lead to the protective layer being scratched and rust de-
veloping.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and after
each use. Do not make any structural changes. For your own safety, please use
original spare parts only. These can be sourced from HUDORA. If parts become
damaged or if sharp edges or corners should develop, the product may not be
used any more. If in any doubt, please contact our service team (http://www.
hudora.de/service/). Store the product in a safe place where it is protected from
the elements, cannot be damaged, and cannot injure anyone.
DISPOSAL ADVICE
At the end of the product’s life, please dispose of it at an appropriate collection
point provided in your area. Local waste management companies will be able to
answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. Therefore, you can find numerous
information on the product, replacement parts, solutions to problems and lost
assembly manuals at http://www.hudora.de/service/.
EN
INSTRUCTIONS ON ASSEMBLY AND USE
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral compo-
nent of the product. Therefore, please store them and the packaging carefully in
case questions arise in the future. Please always include these instructions when
handing on the product to a third party. This product must be assembled by an
adult. This product is not designed for industrial use. The use of the product re-
quires certain capabilities and skills. Always adjust according to the age of the
user and use for the purpose it has been designed for.
TECHNICAL SPECIFICATIONS
Item:
Football Goal Rebound 2 in 1
Item:
76912
Dimensions when assembled: 213 x 153 x 76 cm
Purpose:
Combi rack for football training and individual
shot exercises.
If you have assembly problems or would like further information on the product,
we have all you need and more at http://www.hudora.de/service/.
CONTENTS
19 Goalposts
1 Goal net
5 Tent pegs (for stand fixing)
1 Screw set
4 Cords
1 Tension cord
1 Rebound target
18 Bungee loops
2 Safety bolts
1 Manual
Other items included are meant to facilitate safe transportation and are not re-
quired for the installation and use of the product.
SAFETY INSTRUCTIONS
• WARNING! Not suitable for children under 36 months due to long cords! Stran-
gulation Hazard.
• Prior to use, check all parts of the goal for damages and correct assembly. In
this regard, it is important to check the connecting elements and screw con-
nection for stability and fit. Any sharp edges that might have formed must im-
mediately be removed!
• Warning: Do not climb on the goal frame or net or hang from the goal posts.
There is a serious risk of injury!
• Children should only use the product when they are under adult supervision.
No liability is assumed for damages resulting from incorrect application of the
instruction manual.
ASSEMBLY INSTRUCTION
Note:
Lubricate the connection assemblies on the narrow ends a bit before star-
ting the assembly. That facilitates the assembly and extends the durability of the
product!
1. Assembly of the goal frame
Assemble the goal frame as indicated in fig. 1. Observe that you use the respec-
tively numbered tubes, while leaving out the rebound target fixation (tubes no. 10
(2 parts) and no. 3 (1 part)).
2. Assembly of the goal net
The little flags sewed in the net indicate the upper goal corners. Fasten the goal
net on the goal frame by fastening the hook and loop bands sewed in the net
firstly on the tube parts 11 to 13. Then thread the cords as indicated in fig. 2
around the tubes and knot the loose ends. In order to add additional tension to
the goal net, thread the thicker tension cord at the height of the kinked, rear rods
through the net and knot the loose ends on the rods 11.
All images are examples of the design.
4/8
