ABSCO SHEDS CYCHK Скачать руководство пользователя

Страница: 1 / 25

Absco Industries

Assembly Instruction Manual

LARGE GABLE SHED

N3/C1 FRAME KIT

FOR HIGHLANDER MODELS

Model: CYCHK

02/03/21

1.2

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

LEAVE A REVIEW

Tell us about your experience and

receive a $20 Coles Gift Card.

Visit

www.abscosheds.com.au/review

AU: 1800 029 701

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

This kit is applicable to the following sheds:

The addition of this frame kit will increase the
wind rating of the specified sheds to

Wind rating: N3/C1 as per AS4055-2012.
Suitable for specific cyclonic regions

60303HK
45232HK
30292HK

3060HK
3045HK

WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.

WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.

View of frame kit applied to

3060HK

Where information conflicts with the original
instruction manual, this document is to be
referenced.

This instruction manual is to be used during
the initial construction of the structure.

Содержание CYCHK


























Результаты поиска

Содержание CYCHK

Отзывы:

Похожие инструкции для CYCHK

Бренды по названию

Популярные бренды

ABSCO SHEDS CYCHK, Руководство по сборке и инструкция

Результаты поиска

Содержание CYCHK

Отзывы:

Похожие инструкции для CYCHK

Бренды по названию

Популярные бренды