ABSCO SHEDS CYCHK Скачать руководство пользователя страница 3

Страница: 3 / 25

Absco Industries

Assembly Instruction Manual

LARGE GABLE SHED

N3/C1 FRAME KIT

FOR HIGHLANDER MODELS

Model: CYCHK

02/03/21

1.2

COMPONENT PACKING LIST

FRAME PACK

QTY

COMPONENT

DESCRIPTION

PART

No.

CHK QTY

COMPONENT

DESCRIPTION

PART

No.

CHK

GABLE

WALL BRACE

C2750

VERTICAL

DOOR BRACE

C1555

NON-GABLE

WALL AND ROOF

BRACE

C2100

HORIZONTAL

DOOR BRACE

K0640

PORTAL

COLUMN

C2034

FRONT FRAME

HORIZONTAL

K0285

PORTAL

RAFTER

C1482

FRONT FRAME

MULLION BRACE

C1954

Straight cut to both ends.

20mm Tab notch on one end only

20mm Tab notch on both ends

45mm Lip notch on one end only

45mm Lip notch on both ends

20mm Tab notch + 45mm Lip notch

20mm Tab notch + 45mm Lip notch on both ends

One end: 20mm Tab notch + 45mm Lip notch

SPECIAL NOTCHING, not noted above.

FRAME SECTION IDENTIFICATION GUIDE

The fi rst letter of the part number is used to identify the notching
type. EG.

2940, see below for reference list.

The following digits represent the overall length of the item.
EG. K

2940

Part K2940 is a channel that is 2940mm long with a 20mm Tab notch
at each end.

20mm Tab
notch

45mm Lip
notch

20mm Tab
notch
+
45mm Lip
notch

NOTE:
For 2.3m wide structures the following parts will need to be cut to length.

C1482

to 1106mm

C2750

to 2010mm

Содержание CYCHK


























Результаты поиска

Содержание CYCHK

Отзывы:

Похожие инструкции для CYCHK

Бренды по названию

Популярные бренды

ABSCO SHEDS CYCHK, Руководство по сборке и инструкция

Результаты поиска

Содержание CYCHK

Отзывы:

Похожие инструкции для CYCHK

Бренды по названию

Популярные бренды