background image

31

2.Connection

TEST control: The control switch is connected between PIN 1 and PIN 3. RESET control:

The control switch is connected between PIN 1 and PIN 4. Signal output under testing:

Between PIN 2 and PIN 5.

Test fail signal: Between PIN 6 and PIN 7. Test pass signal: Between PIN 8 and PIN 9.

3.Explain the Input & Output Signal Connection

This tester equips with remote control joints, and the TEST and RESET function of this

instrument can be manipulated by the outside remote control device. These joints provide

the power supply that holds control function, and thus the “Momentary Contact” switch

must be used to act as the controller. Important: These joints must be prohibited to

connect to any other power supplies. If they connect to other power supply, the inside

circuit of this instrument may be damaged.

The output signal provides contact of a relay.

4.Electrical Performance of Interface

Output contact voltage: 24 V AC/DC Max. Current: 100mA

Terminal voltage when the input terminal connects to non-voltage control contact and has

null connection: <10 V DC

VII.Operation Instructions and Procedures

Operation Procedures:

In the case of close and reset, the measured object is connected when the indicator of the

Содержание CS2670A

















































Отзывы: