manualshive.com logo in svg

Huawei V300R001, Замена деталей

Поделиться
Скачать
Huawei V300R001 Скачать руководство пользователя страница 147

Figure 5-61

 Running/Alarm indicator on a power module

Step 12

Confirm the replacement.

1.

Perform a post-replacement inspection.

After the parts replacement, return to the SmartKit page and click 

Replaced

. Then

complete the check after the replacement as prompted.

2.

Check system status.

On the 

Parts Replacement

 page, click 

Inspection

 to check the system status again. If

any inspection item fails, rectify the fault based on the suggestions in the inspection
report.

3.

After the preceding procedure is complete, check services on the host for any storage-
related error.

----End

Follow-up Procedure

After the power module is replaced, label it to facilitate subsequent operations.

5.8.2 Replacing a Power Module (for Dorado6000 V3)

This section describes how to replace a power module. Except that there is a slight difference
on removing and inserting power cables between AC and DC power modules, other
operations performed for them are the same. This section uses AC power modules as an
example.

Impact on the System

During the replacement of a power module, if the redundant power module fails, the
corresponding controller is powered by a BBU and the system reliability degrades.

Prerequisites

l

The spare part is ready.

l

The power module that you want to replace has been located.

OceanStor Dorado V3 Series
Parts Replacement

5 Replacing FRUs

Issue 05 (2019-01-30)

Copyright © Huawei Technologies Co., Ltd.

139

Содержание V300R001





































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды