Huawei TP48200A-DX08A1 Скачать руководство пользователя страница 62

Страница: 62 / 73

TP48200A-DX08A1 and TP48200A-DX08A2 Telecom
Power
User Manual

4 Maintenance

Issue 06 (2019-11-15)

Step 4

Unscrew and remove the heater, as shown in Figure 4-16.

Figure 4-16

Removing a heater

Step 5

Place a new heater and tighten screws.

Step 6

Reconnect all the cables to the heater based on the recorded information.

Step 7

Switch on the heater circuit breaker on the AC PDU.

Step 8

Disconnect the ground cable for the ESD wrist strap, and take off the ESD wrist strap and
ESD gloves.

----End

Follow-up Procedure

Pack the removed component, and return it to the local Huawei warehouse.

4.4.10 Replacing a Battery Temperature Sensor

Prerequisites



You have obtained an ESD wrist strap, ESD gloves, an ESD box or bag, the cabinet door
key, and a tool kit.



The new battery temperature sensor is intact.

Procedure

Step 1

Connect the ground cable for the ESD wrist strap, and put on the ESD wrist strap and ESD
gloves.

Содержание TP48200A-DX08A1










































































Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды

Huawei TP48200A-DX08A1, Руководство пользователя

Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды