Huawei TP48200A-DX08A1 Скачать руководство пользователя страница 61

Страница: 61 / 73

TP48200A-DX08A1 and TP48200A-DX08A2 Telecom
Power
User Manual

4 Maintenance

Issue 06 (2019-11-15)

Procedure

Step 1

Unscrew and remove the air filter, as shown in Figure 4-15.

Figure 4-15

Removing an air filter

Step 2

Place the air filter based on the instructions on the air filter (the labeled side faces upwards,
and the side with a rubber strip faces the cabinet door). Tighten screws to secure the air filter.

----End

4.4.9 Replacing a Heater

Prerequisites



You have obtained an ESD wrist strap, a pair of ESD gloves, the cabinet door key, and a
tool kit.



The new heater is intact.

Before you replace the heater, ensure that the heater circuit breaker is OFF.

Procedure

Step 1

Connect the ground cable for the ESD wrist strap, and put on the ESD wrist strap and ESD
gloves.

Step 2

Switch off the heater circuit breaker on the AC PDU.

Step 3

Record the positions of cables on the heater, and disconnect all the cables.

Содержание TP48200A-DX08A1










































































Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Huawei TP48200A-DX08A1, Руководство пользователя, Страница: 61 / 73

Результаты поиска

Содержание TP48200A-DX08A1

Отзывы: