Huawei TP48200A-DX08A1 Скачать руководство пользователя страница 55

Страница: 55 / 73

TP48200A-DX08A1 and TP48200A-DX08A2 Telecom
Power
User Manual

4 Maintenance

Issue 06 (2019-11-15)

Follow-up Procedure

Pack the removed component, and return it to Huawei local warehouse.

4.4.4 Replacing an SMU

Prerequisites



The cabinet door key is available.



The new SMU is intact.

Procedure

Step 1

Push the locking latch towards the left.

Step 2

Pull the handle outwards and remove the SMU, as shown in Figure 4-8.

Figure 4-8

Removing an SMU

Step 3

Insert the new SMU into the subrack, push the locking latch towards the left, and pull out the
handle.

Step 4

Slide the SMU into the subrack slowly along the guide rails, push in the handle, and then push
the locking latch towards the right.

Step 5

Reset the parameters on the SMU.

Figure 4-9

Installing an SMU

----End

Follow-up Procedure

Pack the removed component and send it to the local Huawei warehouse.

Содержание TP48200A-DX08A1










































































Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды

Huawei TP48200A-DX08A1, Руководство пользователя

Результаты поиска

Содержание TP48200A-DX08A1

Отзывы:

Похожие инструкции для TP48200A-DX08A1

Бренды по названию

Популярные бренды