Huawei SUN2000-100KTL Скачать руководство пользователя страница 68

Страница: 68 / 156

5.7 Connecting DC Input Power Cables

Precautions

D ANGER

● Before connecting the DC input power cable, ensure that the DC voltage is

within the safe range (lower than 60 V DC) and that the three DC switches on

the solar inverter are set to OFF. Failing to do so may result in electric shocks.

● If you turn a DC SWITCH to ON by mistake when connecting or disconnecting

DC input power cables, do not remove or insert DC input terminals. If you need

to remove or insert a DC input terminal, perform the operations provided in

8.2

Power-Off for Troubleshooting

● When the solar inverter operates in grid-tied mode, do not perform

maintenance or operations on the DC circuit, such as connecting or

disconnecting a PV string or a PV module in the PV string. Failing to do so may

cause electric shocks or arcing, which may also cause fire.

WARNING

Ensure that the following conditions are met. Otherwise, the solar inverter may be

damaged, or even a fire could happen.
●

The open-circuit voltage of each PV string must be 1100 V DC or lower under

any circumstances.

●

The polarities of electric connections are correct on the DC input side. The

positive and negative terminals of a PV module connect to corresponding

positive and negative DC input terminals of the solar inverter.

NO TICE

● Ensure that the PV module output is well insulated to ground.
● The PV strings connecting to the same MPPT circuit should contain the same

number of identical PV modules.

● The solar inverter does not support full parallel connection for PV strings (full

parallel connection: PV strings connect to one another in parallel outside the

solar inverter and then connect to the solar inverter separately).

● During the installation of PV strings and the solar inverter, the positive or

negative terminals of PV strings may be short-circuited to ground if the power

cable is not properly installed or routed. In this case, an AC or DC short circuit

may occur and damage the solar inverter. The caused device damage is not

covered under any warranty.

SUN2000-(75KTL, 100KTL, 110KTL, 125KTL) Series

User Manual

5 Electrical Connections

Issue 11 (2021-11-10)

Содержание SUN2000-100KTL





























































































































































Результаты поиска

Содержание SUN2000-100KTL

Отзывы:

Похожие инструкции для SUN2000-100KTL

Бренды по названию

Популярные бренды

Huawei SUN2000-100KTL, Руководство пользователя

Результаты поиска

Содержание SUN2000-100KTL

Отзывы:

Похожие инструкции для SUN2000-100KTL

Бренды по названию

Популярные бренды