Huawei RRU3971 Скачать руководство пользователя

Страница: 72 / 134

----End

7.3 Installing an RRU on U-steel

This section describes the procedure and precautions for installing an RRU on U-steel. An RRU
can be installed on U-steel secured on the ground or a tower. Each piece of U-steel allows only
one RRU to be installed in standard mode.

Prerequisites

Before you install an RRU on U-steel secured on a tower, the RRU and its mounting brackets
are hoisted onto the tower. For details, see

6.1 Hoisting an RRU onto a Tower

The hoist clamp on the main bracket is secured properly.

NOTICE

Do not stand an RRU upright because the RF ports cannot support the weight of the RRU.

Place a foam pad or cardboard under an RRU to protect the RRU housing from damage
during the installation.

Context

Figure 7-22

shows the top view of an RRU installed on U-steel.

NOTICE

When the width of the narrower edges of the U-steel is less than 40 mm (1.57 in.), only the a
and b modes are supported.

7 Installing the RRU

Issue ()

Huawei Proprietary and Confidential

Содержание RRU3971







































































































































Результаты поиска

Содержание RRU3971

Отзывы:

Похожие инструкции для RRU3971

Бренды по названию

Популярные бренды

Huawei RRU3971, Руководство по установке

Результаты поиска

Содержание RRU3971

Отзывы:

Похожие инструкции для RRU3971

Бренды по названию

Популярные бренды