manualshive.com logo in svg

Huawei Quidway S3000-EI Series, Руководство по установке

Поделиться
Скачать
Huawei Quidway S3000-EI Series Скачать руководство пользователя страница 69

Installation Manual 
Quidway S3000-EI Series Ethernet Switches

 

Chapter 7    Optional Interface Modules

 

7-11

 

7.7  6-Port 10Base-T/100Base-TX Module 

7.7.1  Module Panel and the Indicators

 

The panel of 6-port 10Base-T/100Base-TX module is shown in the following figure:

 

 

Figure 7-13

 

6-port 10Base-T/100Base-TX module panel

 

The descriptions of panel indicators are as follows:

 

Table 7-14

 

Meanings of indicators of 6-port 10Base-T/100Base-TX module on the panel

 

 

Indicator

 

Status description

 

ACT/LINK 

Off means that the line is disconnected. On means the line is connected. Blinking means data 
is being received or sent.

 

SPEED

 

Off means 10Mbps and on means 100Mbps.

 

 

7.7.2  Module Interface Cable

 

6-port 10Base-T/100Base-TX module interface matches RJ-45 connector and is 
connected with Category-5 cable. 

 

The module supports MDI/MDI-X auto-sensing 

and can operate in auto-negotiation, full-/half-duplex mode. The following table 
describes the interface attributes.

 

Table 7-15

 

6-port 10Base-T/100Base-TX module interface attributes

 

Attribute

 

6-Port 10Base-T/100Base-TX Module

 

Connector

 

RJ-45 

Interface number

 

6 

Operating mode

 

 

10M/100M half-duplex

 

 

10M/100M full-duplex   

 

Support MDI/MDI-X auto-sensing

 

Transmission medium and 
maximum transmission 
distance

 

Category-5 twisted pair cabling. A maximum transmission distance of 100m is 
supported

 

 

7.8  6-Port 100Base-FX Single Mode/Multi-Mode Module 

7.8.1  Module Panel and the Indicators

 

The panel of 6-port 100Base-FX Single Mode module is shown as follow:

 

Содержание Quidway S3000-EI Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды