manualshive.com logo in svg

Huawei Quidway S3000-EI Series, Руководство по установке

Поделиться
Скачать
Huawei Quidway S3000-EI Series Скачать руководство пользователя страница 58

Installation Manual 
Quidway S3000-EI Series Ethernet Switches

 

Chapter 6  Maintenance and Troubleshooting

 

6-1

 

Chapter 6  Maintenance and Troubleshooting

 

6.1  Power System Failure 

You can check whether the power system of the switch fails by viewing the POWER 
indicator on the front panel. If it is in normal operation, the POWER indicator should 
stay on. Otherwise, please check whether

 

 

The switch power cord is correctly connected.

 

 

The power input to the switch matches the requirement as labeled on the switch.

 

6.2  Configuration System Failure 

After the switch is powered on and the system is normal, the booting information will 
be displayed on the configuration terminal. If the configuration system has any faults, 
there will not be any screen display at the configuration terminal or the displayed 
characters will be totally illegible.

 

I. Troubleshooting when there is no terminal display 

If there is no output information after the configuration is powered on, please check 
whether

 

 

The power supply is normal

 

 

The Console cable is connected correctly

 

If no problems are found after the above-mentioned items have been checked, the 
cause may lie in the Console cable or the settings of the terminal (such as hyper 
terminal) parameters. Please perform the corresponding check.

 

II. Troubleshooting when the terminal display is illegible 

If there is illegible display at the configuration terminal, the cause might lie in the 
parameter setting error at the terminal (such as HyperTerminal).

 

Please confirm the 

terminal parameter (such as hyper terminal) settings: baud rate should be set to 9600, 
data bit to 8, parity to none, stop bit to 1 and flow control to none, and select VT100 
as terminal emulation.

 

 

Содержание Quidway S3000-EI Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды