Huawei Quidway S3000-EI Series Скачать руководство пользователя страница 44

Страница: 44 / 74

Installation Manual
Quidway S3000-EI Series Ethernet Switches

Chapter 4 Powering on Switch for the First Time

4-6

Note:

The boot display may change according to different switches. The display of S3026C Switch is shown in
the following example.

starting….

************************************************

* *

* Quidway S3026 BOOTROM, Version 102 *

* *

************************************************

Creation date: Dec 16 2002, 16:57:31

CPU type : MPC8241

CPU Clock Speed : 200Mhz

BUS Clock Speed : 33Mhz

Memory Size : 64MB

S3026R001 main board self testing..................... (1)

SDRAM fast test..........................................OK! (2)

FLASH fast test..........................................OK! (3)

CPLD test................................................OK! (4)

Port g1/1 has 1000BASE-SX MM module (5)

Port g2/1 has 1000BASE-T GT module (6)

Switch chip test.........................................OK! (7)

PHY test.................................................OK! (8)

Please check port leds.............................finished! (9)

Switch SDRAM fast test...................................OK! (10)

Switch MAC address: 00-BF-FF-BF-FF-BF (11)

Press Ctrl-B to enter Boot Menu... 5 (12)

Line (1) through line (11) are self test information of the system.

Line (5) and (6) are the information about the optional modules installed on the rear
panel and can be different for different modules.

Line (12) asks if the user will enter the BOOT menu and prompts 5 seconds of
waiting.

Press <Ctrl+B> within 5 seconds and enter the BOOT menu.

If you perform no operation or press other keys other than <Ctrl+B>

within the 5

seconds of waiting, the system will enter the auto-booting state when the time
prompt for instruction waiting becomes 0.

Содержание Quidway S3000-EI Series











































































Результаты поиска

Содержание Quidway S3000-EI Series

Отзывы:

Бренды по названию

Популярные бренды

Huawei Quidway S3000-EI Series, Руководство по установке

Результаты поиска

Содержание Quidway S3000-EI Series

Отзывы:

Бренды по названию

Популярные бренды