Huawei FusionServer Pro 2288H V5 Скачать руководство пользователя страница 23

Страница: 23 / 177

Connection status indicator/
Data transmission status
indicator for a 10GE optical
port

Data transmission rate
indicator for a 10GE optical
port

Data transmission rate
indicator for a 10GE electrical
port

Connection status indicator/
Data transmission status
indicator for a 10GE electrical
port

Data transmission status
indicator for a GE electrical
port

Connection status indicator
for a GE electrical port

Data transmission status
indicator for the management
network port

Connection status indicator
for the management network
port

UID indicator

PSU indicator

Indicator Description

Table 2-3

Indicators on the rear panel

Indicator

Description

PSU indicator

Off: No power is supplied.

Blinking green at 1 Hz:

–

The input is normal, the server is in standby state, and
the PSU is in MV6 mode (output voltage is 6.7 V).

–

The input is overvoltage or undervoltage.

–

The PSU is in deep hibernation mode.

Blinking green at 4 Hz: The firmware is being upgraded
online.

Steady green: The power input and output are normal.

Steady orange: The input is normal, but no power output is
supplied.

NOTE

The possible causes of no power output are as follows:

Power supply overtemperature protection

Power output overcurrent or short-circuit

Output overvoltage

Short-circuit protection

Device failure (excluding failure of all devices)

FusionServer Pro 2288H V5 Server
User Guide

2 Hardware Description

Issue 08 (2019-10-30)

Содержание FusionServer Pro 2288H V5


















































































































































































Результаты поиска

Содержание FusionServer Pro 2288H V5

Отзывы:

Похожие инструкции для FusionServer Pro 2288H V5

Бренды по названию

Популярные бренды

Huawei FusionServer Pro 2288H V5, Руководство пользователя

Результаты поиска

Содержание FusionServer Pro 2288H V5

Отзывы:

Похожие инструкции для FusionServer Pro 2288H V5

Бренды по названию

Популярные бренды