Huawei BTS3902E WCDMA Скачать руководство пользователя страница 59

Страница: 59 / 68

Step 9

Replace the BTS3902E.

CAUTION

When removing the BTS3902E, hold the BTS3902E handle with two hands and slightly raise
the BTS3902E to avoid the BTS3902E from falling down.

When an aluminum mounting kit is used, perform the following operations:

Use an M4 Phillips screwdriver to loosen the captive screws on the two hoist clamps on
the main mounting bracket, as shown in

Figure 3-4

Loosening captive screws on the main mounting bracket

Use an M6 Phillips screwdriver to tighten the screws on the attachment plate of the
BTS3902E, as shown in

Figure 3-5

. Use the screw only for removing the BTS3902E to

loosen the connection between the attachment plate and the main mounting bracket, and
then raise the BTS3902E bottom to remove it, as shown in

Figure 3-6

BTS3902E WCDMA
Site Maintenance Guide

3 Replacing the BTS3902E

Issue 06 (2014-05-16)

Huawei Proprietary and Confidential

Содержание BTS3902E WCDMA





































































Результаты поиска

Содержание BTS3902E WCDMA

Отзывы:

Похожие инструкции для BTS3902E WCDMA

Бренды по названию

Популярные бренды

Huawei BTS3902E WCDMA, Описание аппаратуры

Результаты поиска

Содержание BTS3902E WCDMA

Отзывы:

Похожие инструкции для BTS3902E WCDMA

Бренды по названию

Популярные бренды