Huawei BTS3902E WCDMA Скачать руководство пользователя страница 17

Страница: 17 / 68

Item

Silkscreen

Description

DBG

There are two ports:

Network port, used for local
commissioning on the LMT

USB port

, used for local commissioning

with a USB flash drive and for clock
testing

Indicators

RUN

For details, see

2.3 BTS3902E Indicators

ALM

ACT

VSWR

O/E

NOTE

*: The ETH port and OPT1 port cannot be used simultaneously.

**: The security of the USB port is ensured by encryption. The USB port is used for commissioning
the base station rather than importing or exporting the base station configuration.

2.3 BTS3902E Indicators

A BTS3902E has six indicators, which indicate the running status of the BTS3902E.

For details about the indicator positions on the BTS3902E panel, see

2.2 BTS3902E Ports

Table 2-3

describes BTS3902E indicators.

Table 2-3

BTS3902E indicators

Indicator

Color

Status

Description

RUN

Green

Steady on

There is power supply, but the BTS3902E is
faulty.

Off

There is no power supply, or the BTS3902E
is faulty.

Blinking (on for
1s and off for 1s)

The BTS3902E is working properly.

Blinking (on for
0.125s and off for
0.125s)

Software is being loaded to the BTS3902E,
or the BTS3902E is not started.

BTS3902E WCDMA
Hardware Description

2 BTS3902E Overview

Issue 09 (2014-05-16)

Huawei Proprietary and Confidential

Содержание BTS3902E WCDMA





































































Результаты поиска

Содержание BTS3902E WCDMA

Отзывы:

Похожие инструкции для BTS3902E WCDMA

Бренды по названию

Популярные бренды

Huawei BTS3902E WCDMA, Описание аппаратуры

Результаты поиска

Содержание BTS3902E WCDMA

Отзывы:

Похожие инструкции для BTS3902E WCDMA

Бренды по названию

Популярные бренды