Huawei 50082920 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 112

background image

Figure 5-39

Testing the conduction and connections of wires

Step 3

Gently shake the connector and repeat

to check whether the metal contact strips are in

good contact with the core wires and Ethernet ports, as shown in

Figure 5-40

.

Figure 5-40

Checking the reliability

The procedure for testing a crossover cable is the same as that for testing a straight-through
cable except for the sequence in which the indicators turn on, which depends on the wire
connections of a crossover cable.

The Ethernet cable is qualified if the indicators turn on in the following sequence:

At the master (left) section of the tester, the indicators turn on in the sequence of 1-8-G. At the
slave (right) section of the tester, the indicators turn on in the sequence of 3-6-1-4-5-2-7-8-G.

If the indicators do not come on in this sequence, the Ethernet cable is unqualified.

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

44

«
...
48
49
50
51
52
...
»

Содержание 50082920

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 50082920

AirPlusXtremeG DI-624

Бренд: D-Link Страницы: 83

AirPlusXtremeG DI-624

Бренд: D-Link Страницы: 97

Бренд: 3Com Страницы: 2

Бренд: LevelOne Страницы: 14

Бренд: IP-COM Страницы: 2

Бренд: EE Страницы: 207

Бренд: 4IPNET Страницы: 194

MetroLinq2.5 ML2.5-60-35

Бренд: IgniteNet Страницы: 9

Бренд: 3Com Страницы: 8

Бренд: Hisense Страницы: 5

Бренд: Innoband Страницы: 83

Бренд: DQ Technology Страницы: 43

Бренд: Dynalink Страницы: 2

Бренд: Proxim Страницы: 32

Бренд: Nortel Страницы: 68

Бренд: Sierra Wireless Страницы: 74

Бренд: Air Live Страницы: 75

Бренд: Franklin Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды