background image

NOTE

Place at least three cleaning tissues on the work bench. As shown in 

Figure 5-96

, wipe the end of

an optical connector from left to right or from right to left on a cleaning tissue, and then move the
connector end to the unused part of the cleaning tissue to continue.

2.

Cover an unused optical module with a protective cap to prevent dust, as shown in

Figure 5-97

.

Figure 5-97

 Installing a protective cap

 

If no protective cap is available, use fibers to protect the optical module, as shown in

Figure 5-98

.

Figure 5-98

 Using fibers to protect an optical module

 

3.

Cover unused optical connectors with protective caps, as shown in 

Figure 5-99

, and then

lay out fibers on the fiber rack or coil them in a fiber management tray to prevent fibers
from being squeezed.

Figure 5-99

 Installing a protective cap on a fiber

 

4.

If a receptacle or an optical connector has not been used for a long time and is not
covered with a protective cap, you need to clean it before using it. Clean a receptacle
with a cotton swab, as shown in 

Figure 5-100

. Clean an optical connector with cleaning

tissues.

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

96

Содержание 50082920

















































































































Отзывы: