Huawei 50082920 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 112

background image

Com
pone
nt

No.

Applic
able
Scope

Check Item

4

General

Signal cables are orderly routed and not crossed, twisted, or
winded (cables can be crossed at 1 m out of the cabinet). The
bend radius of cables meets requirements, and the cables are
not excessively bent.

5

General

Signal cables are not damaged or broken and have no splices.
Sufficient cable length is reserved. The reserved cables are
twined and placed properly to facilitate subsequent
maintenance.

6

Indoor

AP

The optical, power, network, and feeder cables are bundled
using straps (one strap every 0.5 m) and securely fastened.

7

Outdoor

AP

The signal cables shall be bundled at even intervals (about
1000 mm), not too tight or too loose. The cables shall be
bundled properly with cable ties placed in neat order. Cut off
redundant cable ties and remove burrs from them to avoid
injuries. The cables shall be fixed using fasteners or ageing-
resistant outdoor metal binding straps.

8

General

Keep the signal cables away from heat sources and use heat
insulation materials to insulate the cables from the heat
sources. Do not place signal cables on the air vents of the
cabinet to avoid affecting subrack heat dissipation or cable
lifetime.

9

General

Pigtail layout should meet the following requirements:

l

Pigtails are not strained or twisted at the bent parts. They
are bundled by binding tape with appropriate force.

l

Pigtails can be pulled back and forth easily inside the
cable tie and are not bent at a right angle.

l

Pigtails are not squeezed by other cables or objects.

l

The flange must be fixed.

l

Pigtails are protected with protective tubes or enveloped
in troughs when they are routed outside the cabinet. The
protective tubes are bundled and processed to prevent
cutting.

l

The optical fiber cannot be folded or twisted, and the
pigtail cannot be squeezed. The binding diameter of an
optical fiber must be larger than 6 cm.

l

The pigtail connection points must be clean and dustless.
Fiber connectors and optical ports that are not used must
be protected with protective caps or plugs. Cleaning must
be carried out in strict accordance with Huawei tool
specifications.

10

General

The feeder cables shall not be bent or twisted, with no copper
wire exposed.

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

102

«
...
106
107
108
109
110
...
»

Содержание 50082920

















































































































Отзывы:

Нет отзывов

Похожие инструкции для 50082920

Бренд: Quantum Страницы: 8

Бренд: Quantum Страницы: 21

Бренд: Quantum Networks Страницы: 27

Бренд: NetComm Страницы: 55

Бренд: Aruba Страницы: 20

Бренд: Pakedge Страницы: 6

Бренд: Ubiquiti Страницы: 33

Бренд: Linksys Страницы: 124

Бренд: D-Link Страницы: 64

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 36

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 65

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды