Huawei 196KTL-H0 Скачать руководство пользователя страница 80

Страница: 80 / 122

No.

Parameter

Description

Remarks

Grid voltage

jump

triggering

threshold (%)

Specifies the LVRT or HVRT threshold for

triggering a transient voltage jump of a power

grid. A transient voltage jump indicates that the

inverter cannot immediately disconnect from

the power grid when the power grid is

abnormal due to transient changes.

Zero current

due to power

grid fault

Certain countries and regions have

requirements on the output current during

high/low voltage ride-through. In this case, set

this parameter to Enable. After this parameter

is set to Enable, the output current is less than

10% of the rated current during high/low

voltage ride-through.

This parameter is

displayed when LVRT

or HVRT is set to

Enable.

Active

islanding

protection

Specifies whether to enable the active islanding

protection function.

Automatic

OFF due to

communicati

interrupted

The standards of certain countries and regions

require that the inverter must shut down after

the communication is interrupted for a certain

time.

Automatic

ON due to

communicati

on resumed

If this parameter is set to Enable, the inverter

automatically starts after communication

recovers. If this parameter is set to Disable, the

inverter needs to be started manually after

communication recovers.

Communicati

interruption

duration

(min)

Specifies the duration for determining

communication interruption. Used for

automatic shutdown for protection in case of

communication interruption.

Soft start/

boot time (s)

Specifies the duration for the power to

gradually increase when the inverter starts.

Soft start

time after

grid failure

(s)

Specifies the time for the power to gradually

increase when the inverter restarts after the

power grid recovers.

TCP

heartbeat

interval (s)

Specifies the TCP link timeout period for the

solar inverter to connect to the management

system.

TCP frame

length

Specifies the maximum length of the TCP frame

sent by the northbound device to the solar

inverter.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

7 Man-Machine Interactions

Issue 07 (2021-07-08)

Содержание 196KTL-H0



























































































































Результаты поиска

Содержание 196KTL-H0

Отзывы:

Похожие инструкции для 196KTL-H0

Бренды по названию

Популярные бренды

Huawei 196KTL-H0, Руководство пользователя

Результаты поиска

Содержание 196KTL-H0

Отзывы:

Похожие инструкции для 196KTL-H0

Бренды по названию

Популярные бренды