Huawei 196KTL-H0 Скачать руководство пользователя страница 92

Страница: 92 / 122

Step 7 Wait for 15 minutes and troubleshoot or repair the inverter.

WARNING

● Do not open the host panel for maintenance if the solar inverter is emitting

odor or smoke, or has obvious exceptions.

● If the solar inverter does not emit odor or smoke and is intact, repair or restart

it based on the alarm handling suggestions. Do not stand in front of the solar

inverter during the restart.

----End

8.3 Routine Maintenance

Maintenance Item

To ensure that the inverter can operate properly for a long term, you are advised

to perform routine maintenance on it as described in this chapter.

CA UTION

● Before cleaning the system, connecting cables, and maintaining the grounding

reliability, power off the system and ensure that the three DC switches on the

inverter are OFF.

● If you need to open the maintenance compartment door in rainy or snowy

days, take protective measures to prevent rain or snow entering the

maintenance compartment. If unavoidable, do not open the maintenance

compartment door.

Maintenance list

Item

Check Method

Maintenance

Interval

● Cleanness of

air intake and

exhaust vents

● Fans

● Check whether there is dust on

the air intake and exhaust vents.

If necessary, remove the baffle

of the air intake vent.

● Check whether the fans produce

abnormal sounds during

operation.

Once every 6 to 12

months

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

8 Maintenance

Issue 07 (2021-07-08)

Содержание 196KTL-H0



























































































































Результаты поиска

Содержание 196KTL-H0

Отзывы:

Похожие инструкции для 196KTL-H0

Бренды по названию

Популярные бренды

Huawei 196KTL-H0, Руководство пользователя

Результаты поиска

Содержание 196KTL-H0

Отзывы:

Похожие инструкции для 196KTL-H0

Бренды по названию

Популярные бренды