Huawei 196KTL-H0 Скачать руководство пользователя страница 106

Страница: 106 / 122

Alarm

Alarm Name

Alarm

Severity

Cause

Troubleshooting Suggestions

2065

Upgrade Failed

or Software

Version

Unmatch

Minor

Cause ID=1
The upgrade does not

complete normally.

1. Perform an upgrade again.
2. If the upgrade fails several

times, contact your dealer.

2066

License Expired Warning

Cause ID=1
1. The privilege license

has entered the grace

period.

2. The privilege feature

will be invalid soon.

1. Apply for a new license.
2. Load a new license.

2086

External fan

abnormal

Major

External fan short-

circuited, power supply

insufficient, or air channel

blocked
Cause ID 1–3: fans 1–3

1. Shut down the fan, turn off

the DC switch, check

whether the fan blades are

damaged, and clear the

foreign matter around the

fan.

2. Reinstall the fan, turn on

the DC switch, and wait for

the inverter to start. If the

fault persists after 15

minutes, replace the

external fan.

2087

Internal fan

abnormal

Major

Cause ID=1
The internal fan is short-

circuited, the power

supply is insufficient, or

the fan is damaged.

Turn off the AC output switch

and then the DC input switch.

Turn them on after 5 minutes

and wait for the inverter to

connect to the power grid. If

the fault persists, contact your

dealer or Huawei technical

support.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

8 Maintenance

Issue 07 (2021-07-08)

Содержание 196KTL-H0



























































































































Результаты поиска

Содержание 196KTL-H0

Отзывы:

Похожие инструкции для 196KTL-H0

Бренды по названию

Популярные бренды

Huawei 196KTL-H0, Руководство пользователя

Результаты поиска

Содержание 196KTL-H0

Отзывы:

Похожие инструкции для 196KTL-H0

Бренды по названию

Популярные бренды