manualshive.com logo in svg

HTP SSC-20TC, Инструкция по использованию и уходу, Страница: 13 / 20

Поделиться
Скачать
HTP SSC-20TC Скачать руководство пользователя страница 13

lp-770 Rev. 000 Rel. 000 Date 6.21.21

13

Part 4 - Heater Control and Wiring

C. Wiring Diagrams

Figure 6 - Tankless Coil Boiler Application - Wiring with Circulators

Figure 7 - Tankless Coil Boiler Application - Wiring with Zone Valves

A. Control

Install control element into the control well and tighten into place with screws on the control body. Thermal conductive paste is recommended. 

Once the control is operational, it is important to make sure the control is maintaining the desired operating temperature.

B. Wiring

Wiring is to be done in accordance with all applicable local and state codes. Turn off all power related to the boiler before starting any wiring 

procedures.It is recommended that a disconnect switch be installed between the boiler control and the water heater.

CAUTION

When wiring the water heater and controls be sure to label all wires to ease future maintenance. Wiring errors can cause improper and 

dangerous operation.

Содержание SSC-20TC





















Отзывы:

Нет отзывов