lp-608 Rev. 000 Rel. 001 Date 3.15.18
9
RE-INSPECTION OF T&P RELIEF VALVES: T&P valves should
be inspected AT LEAST ONCE EVERY THREE YEARS, and
replaced if necessary,
by a licensed plumbing contractor or
qualified service technician to ensure that the product has not
been affected by corrosive water conditions and to ensure that
the valve and discharge line have not been altered or tampered
with illegally. Certain naturally occuring conditions may corrode
the valve and its components over time, rendering the valve
inoperative. Such conditions can only be detected if the valve
and its components are physically removed and inspected.
Do
not attempt to conduct an inspection on your own.
Contact
your plumbing contractor for a re-inspection to assure continued
safety.
FAILURE TO RE-INSPECT THE T&P VALVE AS DIRECTED COULD
RESULT IN UNSAFE TEMPERATURE AND/OR PRESSURE BUILD-
UP WHICH CAN RESULT IN PROPERTY DAMAGE, SERIOUS
PERSONAL INJURY, OR DEATH.
Do not thread a cap or plug into the relief valve or block relief
valve outlet line under any circumstances! Explosion and property
damage, serious injury, or death may result.
F. Scalding
Mixing valves are recommended for reducing point of use water
temperature by mixing hot and cold water in branch water lines. It
is recommended that a mixing valve complying with the Standard
for Temperature Actuated Mixing Valves for Hot Water Distribution
Systems, ASSE 1017, be installed. Mixing valves can reduce but do
not eliminate the risk of scalding.
To avoid scalding:
•
Set the water heater set point temperature as low as possible.
•
Feel water before bathing or showering.
•
If thermostatic valves are required, use devices specifically
designed for such purpose. Install these devices in accordance
with instructions provided by the manufacturer.
Failure to install a temperature limiting or mixing valve and follow
these instructions could result in property damage, severe personal
injury, or death due to scalds.
•
Make certain that the drain valve is completely closed.
•
Open the shut-off valve in the cold water supply line.
•
Open the hot water faucets to allow air to vent from the heater
and piping.
•
Allow sufficient time for the heater to completely fill with
water.
•
Verify elements are installed correctly. Check for leaks.
G. Filling the Heater
This water heater can
deliver scalding water. Be
careful whenever using
hot water to avoid scalding
injury. Certain appliances
such as dishwashers and
automatic clothes washers
may require increased
water temperatures. By
setting the thermostat
on this heater to obtain
the increased water
temperature required by
these appliances you may
create the potential for
scald injury.
To protect against injury,
install a mixing valve in the
water system. This valve
will reduce point of use
discharge temperatures by
mixing cold and hot water
in branch supply lines.
Such valves are available
from your local plumbing
supplier.
Table 1 details the relationship of water temperature and time with
regard to scald injury and may be used as a guide in determining the
safest water temperature for your applications.
To avoid water damage or scalding due to relief valve operation:
•
Discharge line must be connected to relief valve outlet and
run to a safe place of disposal. Terminate the discharge line
in a manner that will prevent possibility of severe burns or
property damage should the relief valve discharge.
•
Discharge line must be as short as possible and the same
size as the valve discharge connection throughout its
entire length.
•
Discharge line must pitch downward from the valve
and terminate at least 6” above the floor drain, making
discharge clearly visible.
•
The discharge line shall terminate plain, not threaded, with
a material serviceable for temperatures of 375
o
F or greater.
•
Do not pipe discharge to any location where freezing could
occur.
•
No valve may be installed between the relief valve and
heater or in the discharge line. Do not plug or place any
obstruction in the discharge line.
•
Test the operation of the relief valve after filling and
pressurizing the system by lifting the lever. Make sure the
valve discharges freely. If the valve fails to operate correctly,
immediately replace with a new properly rated relief valve.
•
Test T&P valve at least once annually to ensure the
waterway is clear. If valve does not operate, turn the heater
“off” and call a plumber immediately.
•
Take care whenever operating relief valve to avoid scalding
injury or property damage.
FAILURE TO COMPLY WITH THE ABOVE GUIDELINES COULD
RESULT IN FAILURE OF RELIEF VALVE OPERATION, RESULTING
IN POSSIBILITY OF SUBSTANTIAL PROPERTY DAMAGE, SEVERE
PERSONAL INJURY, OR DEATH.
When filling the water heater, open a hot water tap to release air in
the tank and piping. The tank must be full of water before the heater
is turned on. Failure to ensure the water heater is full before turning
it on could result in damage to the water heater and other property
damages. Such damages ARE NOT covered by water heater warranty.