HT ECLIPSE HT9025 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 47

HT ECLIPSE HT9025 Скачать руководство пользователя страница 28

ECLIPSE - HT9025

EN - 27

5.7. CAPACITANCE

MEASUREMENT

CAUTION

Before carrying out capacitance measurements on circuits or capacitors, cut
off power supply from the circuit being tested and let all capacitance in it be
discharged. When connecting the multimeter and the capacitance to be
measured, respect the correct polarity (when required).

Fig. 29: Use of the instrument for Capacitance measurement

1. Select

position

:

CAP

2. Press

the

MODE/VFD

key until the symbol

“

nF

”

is displayed.

3. Insert the red cable into input terminal

VHz% CAP

:

and the black cable into

input terminal

COM

.

4. Press

the

REL/

S

key before carrying out measurement (see § 4.3.5).

5. Position the leads at the ends of the capacitor to be tested, respecting, if necessary,

the positive (red cable) and negative (black cable) polarity (see Fig. 29). The value is
shown on the display.

According to capacitance, the instrument may take several

seconds to display the correct final value.

The bargraph is not active in this

function.

6. The

message

“

OL

”

indicates that the value of capacitance exceeds the maximum

measurable value.

7.  To use the HOLD and RANGE functions, see § 4.2
8.  To use the internal functions, see § 4.3
9.  To save the measured result, see § 4.3.4

«
...
26
27
28
29
30
...
»

Содержание ECLIPSE HT9025
















































Отзывы:

Нет отзывов