HP Vectra VL400 Скачать руководство пользователя страница 61

Страница: 61 / 74

Solving Problems 61 of 74

HP Web Services

Your Vectra

Setting Up

Using

Warranty and

Support Service

Installing

Components

Solving

Problems

Hard Disk, DVD or CD-ROM Drive Test
Error

1 of 2

Have you checked that...

How

You have not received a S.M.A.R.T. alert
from the HP TopTools Agent indicating
that your hard disk drive is defective

Important: Carry out an immediate data backup, then contact your
local Customer Care Center (refer to the Warranty and Support
Service section).

The drive is correctly configured in the
PC’s Setup program

1 Switch the PC OFF then ON.
2 When the message

Press F2 to Enter Setup

appears, press the

key.

3 Check the drive is enabled and the correct type is selected.

The hard disk, DVD or CD-ROM drive is
working

Run e-DiagTools from the Brio Assist CD-ROM (Drivers & Utilities)
to test your hard drive. To test your DVD or CD-ROM drive, run e-
DiagTools from the Utility Partition on your hard drive (

refer to

page 21

You are using the latest BIOS for your
PC

Download the latest BIOS and instructions for its installation from
HP’s support web site.

Содержание Vectra VL400











































































Результаты поиска

Содержание Vectra VL400

Отзывы:

HP Vectra VL400, Часто задаваемые вопросы, Страница: 61 / 74

Результаты поиска

Содержание Vectra VL400

Отзывы: