HP StorageWorks A7298A Скачать руководство пользователя страница 32

Страница: 32 / 92

Installing the SCSI Miniport Driver

Host Bus Adapter for Windows and Linux Installation Guide

Windows Server 2003 Device Driver Installation

This section describes the instructions for installing the Windows Server 2003
SCSI Miniport driver.

Windows Server 2003 System Requirements

Ensure that your system meets these minimum requirements:

■

Installed HBA

■

Ensure the HP Setup and Configuration CD for Itanium(R) 2-based servers is
in the server or the driver has been downloaded from the web and copied to
the server hard drive.

■

StorageWorks Fibre Channel Storage subsystem (interconnect device and
storage device)

Installing the Windows Server 2003 SCSI Miniport Driver

This section contains the steps for installing the Windows Server 2003 SCSI
Miniport device driver on a Windows Server 2003.

From the Windows Server 2003 desktop:

1. Click Start > Settings > Control Panel.

2. Double-click Administrative Tools.

3. Double-click Computer Management.

4. Click Device Manager.

5. Open the SCSI and RAID controllers item in the list.

6. Choose the Drivers tab.

7. Choose Update Driver.

8. Choose Install the software automatically (Recommended) and click Next.

9. Click Finish.

10. Click Yes to restart Windows Server 2003.

11. Verify the device driver installation:

Click Start > Settings > Control Panel.

Double-click the System icon.

Click Device Manager.

Содержание StorageWorks A7298A





























































































Результаты поиска

Содержание StorageWorks A7298A

Отзывы:

Похожие инструкции для StorageWorks A7298A

Бренды по названию

Популярные бренды

HP StorageWorks A7298A, Руководство по установке

Результаты поиска

Содержание StorageWorks A7298A

Отзывы:

Похожие инструкции для StorageWorks A7298A

Бренды по названию

Популярные бренды