manualshive.com logo in svg

HP ProLiant DL320 Generation 5p, Руководство пользователя

Поделиться
Скачать
HP ProLiant DL320 Generation 5p Скачать руководство пользователя страница 31

 

Hardware options installation 31 

The following table lists some, but not all, possible configurations. For best performance, HP recommends 

dual-bank interleaved mode configurations. 

    

Slot 1A 

Slot 2B 

Slot 3A 

Slot 4B 

Total memory 

Mode 

512 

MB 

— — — 512 

MB Single-bank 

512 MB 

— 

512 MB 

— 

1 GB 

Single-bank interleaved 

1 

GB 

— — — 1 

GB  Single-bank 

1 GB 

— 

1 GB 

— 

2 GB 

Single-bank interleaved 

1 GB 

1 GB 

1 GB 

1 GB 

4 GB 

Dual-bank interleaved 

2 GB 

2 GB 

2 GB 

2 GB 

8 GB 

Dual-bank interleaved 

 

 

Installing DIMMs 

1.

 

Power down the server (on page 

20

). 

2.

 

Remove the server from the rack (on page 

20

). 

3.

 

Remove the primary access panel (on page 

21

). 

4.

 

Open the DIMM slot latches. 

5.

 

Install the DIMM. 

 

6.

 

Install the access panel. 

7.

 

Install the server into the rack. 

 

Hard drive options 

The server provides non-hot plug capability through an embedded SATA controller. To obtain hot-plug 

capability, install an optional controller and hot-plug cable option kit. 

 

Содержание ProLiant DL320 Generation 5p











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды