HP Jetdirect J7949e Скачать руководство пользователя

Страница: 189 / 232

ENWW

HP Jetdirect Configuration Page 189

IPX/SPX Protocol Information

Information in this section of the Jetdirect configuration page is
described in

Table 9.5

. For error messages, see

Table 9.9

Table 9.5

IPX/SPX Configuration Information (1 of 2)

Message

Description

STATUS:

Indicates the current IPX/SPX protocol status.

READY: Indicates the HP Jetdirect print server is awaiting
data over IPX/SPX.

DISABLED: Indicates that IPX/SPX was manually disabled.

INITIALIZING: Indicates that the print server is registering
the node address or name. An additional status message
may also be displayed.

An error code and message is displayed if the print server
is not ready. For more information, see

Table 9.9

PRIMARY FRAME
TYPE:

Specifies the frame type selection on the Jetdirect print
server.

AUTO SELECT: The print server automatically senses and
limits the frame type to the first one detected.

EN_8023: Limits the frame type to IPX over IEEE 802.3
frames. All others will be counted and discarded.

EN_II: Limits the frame type to IPX over Ethernet frames.
All others will be counted and discarded.

EN_8022: Limits the frame type to IPX over IEEE 802.2 with
IEEE 802.3 frames. All others will be counted and
discarded.

EN_SNAP: Limits the frame type to IPX over SNAP with
IEEE 802.3 frames. All others will be counted and
discarded.

Содержание Jetdirect J7949e









































































































































































































































Результаты поиска

Содержание Jetdirect J7949e

Отзывы:

Похожие инструкции для Jetdirect J7949e

Бренды по названию

Популярные бренды

HP Jetdirect J7949e, Руководство администратора

Результаты поиска

Содержание Jetdirect J7949e

Отзывы:

Похожие инструкции для Jetdirect J7949e

Бренды по названию

Популярные бренды