background image

ENWW

FTP Printing 158

Example of an FTP Session

This is an example of a typical FTP printing session:

C:\> 

ftp 192.168.45.39

Connected to 192.168.45.39.
220 JD FTP Server Ready
User <192.168.45.39:<none>>: 

susan_g

001 Username Ok, send identity <email address> as password
Password:
230- Hewlett-Packard FTP Print Server Version 2.0
Directory:

Description:

-----------------------------------------------------
PORT1 

Print to port 1 HP LaserJet 9050

To print a file, use the command: put <filename> [portx]
or cd to a desired port and use: put <filename>.

Ready to print to PORT1

230 User logged in.
ftp> 

pwd

257 “/” is current directory. <“default port is : /PORT1> 
HP LaserJet 9050”
ftp> 

cd port1

250 Changed directory to “/PORT1”
ftp> 

pwd

257 “/PORT1” is current directory. “HP LaserJet 9050”
ftp> 

bin

200 Type set to I. Using binary mode to transfer files.
ftp> 

put d:\atlas\temp\ftp_test.ps

200 PORT command successful.
150 Opening BINARY mode data connection
226- Ready
226- Processing job
226 Transfer complete
31534 bytes sent in 0.04 seconds <788.35 Kbytes/sec>
ftp> 

quit

221 Goodbye

C:\>

Содержание Jetdirect J7949e









































































































































































































































Отзывы: