background image

4

Downloading Software

Observe the following when downloading the OS software to the 
Switch 2000:

filename

.swi

 and

 

filename

.fdd

 must be in the same direc-

tory.

filename

 must be the same for both files (that is, the files must 

be the 

.swi

 and 

.fdd

 file pair from the disk or from the self-

extracting 

j3100a.exe

 file. 

For the above reasons, avoid placing the 

filename

.swi and 

filename

.fdd

 in separate directories, and avoid renaming them.

N o t e

The latest version of the Switch 2000 OS supports all Switch 2000 Modules 
currently available. If you are installing more than one type of Switch 2000 
module and/or if it is necessary to download a new version of the Switch 2000 
OS, use the latest version available. To support the 10Base-FL Module, use OS 
version A.02.01 or later. The Switch 2000 Ethernet and 100VG Modules operate 
with 

any

 version of Switch 2000 OS software. For more on software compat-

ibility, see the 

readme.txt

 file included on the disk and in the compressed, 

self-extracting 

j3100a.exe

 file from the electronic sources mentioned 

above.

How To Download the OS

Use this procedure if you need to download a new OS version to your Switch 
2000. The procedure describes how to use a personal computer (PC) to 
download the OS. (If you are using a UNIX workstation, refer to the Note on.) 
The files used in this procedure are described under “Software Sources and 
Content” on page 3.

1.

Do one of the following:

If the source of your OS files is the disk shipped with the 
10Base-FL Module, copy the files from the disk into the DOS directory 
you will use for downloading to the switch. Then go to on the next 
page.

If the source of your OS files is the self-extracting 

j3100a.exe

 file 

from an electronic source (see “Software Sources and Content” on 
page 3):

i.

Copy the 

j3100a.exe

 file into the DOS directory you will use 

for downloading to the switch.

ii.

Execute the file to decompress and extract its contents.

blue_2b.fm5  Page 4  Monday, September 23, 1996  8:03 AM

Содержание J3109A































Отзывы: