HP HP-UX 11i v3 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 125

background image

6 Troubleshooting HP APA

This chapter contains a diagnostic map to help you solve problems that might occur when you
use HP APA. Use this chapter with the appropriate HP and third-party switch documentation
to solve as many problems as possible at your level.

Operation

Network problems can occur for a number of reasons. The diagnostic map in this chapter help
you to isolate the problem. The following figure explains how to use the diagnostic map:

The left-hand column

asks questions about

the status of specific

events that occur as

you use the system.

The right-hand column

diagnoses negative

responses to those

questions.

After you isolate the problem, the map refers you to other chapters for instructions on using the
various problem solving tools and utilities. The map also refers you to other manuals for more
complete diagnostic information for particular devices and software products.

You might experience problems that are not documented in this manual when you use the HP
APA software with other products. See the documentation for the other products for additional
information.

Getting started

Before you start troubleshooting, ensure that the communications hardware is ready for use.
Verify the following:
•

The system's physical cable connections (the Ethernet connection and the transceiver
connection) are properly installed. See the documentation for your system and the NIC.

•

Event logging is enabled in order to monitor network events. For information about the
Network Tracing and Logging (NetTL) tool, see

“nettl tracing and logging tool” (page 81)

.

For information about logging messages to

syslog

, see

“Logging messages to the syslog.log

file” (page 43)

.

Also see the product release notes for up-to-date information on known problems.

Solving HP APA problems

System on?

NO

YES

Turn on the power to your system. See the system manual for your
system's startup procedure and any problem solving information.

Operation

57

«
...
55
56
57
58
59
...
»

Содержание HP-UX 11i v3






























































































































Отзывы:

Нет отзывов

Похожие инструкции для HP-UX 11i v3

Бренд: cable matters Страницы: 12

Бренд: Velleman Страницы: 20

Бренд: SWEEX Страницы: 3

FreeAgent DockStar

Бренд: Seagate Страницы: 13

Бренд: Cables to Go Страницы: 21

Бренд: S2Konnect Страницы: 26

Бренд: PureLink Страницы: 16

Бренд: Toto Link Страницы: 1

Бренд: UCONNECT INTERNATIONAL Страницы: 8

Бренд: Alvarion Страницы: 2

Бренд: Kramer Страницы: 3

Бренд: Supermicro Страницы: 21

Бренд: Hainbuch Страницы: 64

Бренд: StarTech.com Страницы: 10

Бренд: Tripp Lite Страницы: 25

Бренд: WAFER Страницы: 12

Бренд: Abus Страницы: 23

ConnectLine Phone Adapter 2.0

Бренд: oticon Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды