HP HP-UX 11i v3 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 125

background image

POLLING_INTERVAL 10000000
DEAD_COUNT 3
LM_RAPID_ARP off
LM_RAPID_ARP_INTERVAL 1000000
LM_RAPID_ARP_COUNT 10
FAILOVER_GROUP lan900
STATIONARY_IP 192.1.1.1
STANDBY lan11 3
PRIMARY lan10 5

7.

Compare the

/etc/lanmon/lanconfig.ascii

file with the

/tmp/filename

file.

If they are not the same, decide which file you want to use. If you want to use the file in

/tmp

, copy that file to

/etc/lanmon/lanconfig.ascii

.

8.

Edit the

/etc/lanmon/lanconfig.ascii

file and change the number of ports in the

failover groups, the dead count, poll interval, rapid ARP setting, rapid ARP interval, rapid
ARP count, and stationary IP address. The following example shows a failover group entry
that contains an IPv6 address:

FAILOVER_GROUP lan901
STATIONARY_IP fe80::1
STANDBY lan11 3
PRIMARY lan4 5

9.

Verify that the configuration in

/etc/lanmon/lanconfig.ascii

is still valid by using

the

lancheckconf

command.

10. Create the failover groups specified in the configuration file by using the

lanapplyconf

command.
This command creates the specified failover groups.
Check the failover groups by using the

nwmgr -S apa

and

netstat -in

commands.

NOTE:

If you later want to delete all the failover groups created, enter the

landeleteconf

command.

11. The failover group is now operational. A reboot will restart the failover group as long as

the

/etc/lanmon/lanconfig.ascii

file is intact.

Example: Configuring a failover group

Suppose you want to configure a simple, two-port LAN Monitor failover group on a K-class
system. You enter the

netstat

and

ioscan

commands as follows:

# netstat -in
Name Mtu Network Address Ipkts Opkts
lan1 1500 192.1.1.0 192.1.1.153 9504123 12437048
lan0 1500 191.1.1.0 191.1.1.1 11202 257458
lo0 4136 127.0.0.0 127.0.0.1 417 417

# ioscan -fkC lan
Class I H/W Path Driver S/W State H/W Type Description
========================================================================
lan 1 8/8/1/0 igelan CLAIMED INTERFACE HP PCI 1000Base-T Core
lan 2 8/8/2/0 igelan CLAIMED INTERFACE HP PCI 1000Base-T Core
lan 3 8/12/1/0 igelan CLAIMED INTERFACE HP PCI 1000Base-T Core
lan 4 8/12/2/0 igelan CLAIMED INTERFACE HP PCI 1000Base-T Core
lan 0 10/12/6 lan2 CLAIMED INTERFACE Built-in LAN
#

The

netstat

output shows that

lan1

is currently configured with IP address 192.1.1.153. The

ioscan

output shows spare 1000Base-T devices

lan2

,

lan3

, and

lan4

.

You decide that

lan2

will be the standby link for the failover group, with

lan1

as the active

device.
To configure the failover group, do the following:

100

Configuring HP APA by editing files

«
...
98
99
100
101
102
...
»

Содержание HP-UX 11i v3






























































































































Отзывы:

Нет отзывов

Похожие инструкции для HP-UX 11i v3

Бренд: Airlink101 Страницы: 4

Бренд: 3idee Страницы: 7

Бренд: 3idee Страницы: 7

Бренд: 3idee Страницы: 7

hp27-o VESA Adapter

Бренд: 3idee Страницы: 9

Бренд: TEXIO Страницы: 49

Бренд: Ratoc Systems Страницы: 20

Бренд: Telstra Страницы: 28

Бренд: UNICOM Страницы: 7

Бренд: Manhattan Страницы: 2

ConnectLine Phone Adapter 2.0

Бренд: oticon Страницы: 26

Бренд: Zonet Страницы: 19

Бренд: Mitsubishi Electric Страницы: 3

MELSEC FX3U-485ADP-MB

Бренд: Mitsubishi Electric Страницы: 8

FX3U-485ADP-MBH

Бренд: Mitsubishi Electric Страницы: 2

PAC-USWHS002-WF-2

Бренд: Mitsubishi Electric Страницы: 8

Бренд: Mitsubishi Electric Страницы: 3

Бренд: Mitsubishi Electric Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды