HP HP-UX 11i v3 Скачать руководство пользователя страница 113

Страница: 113 / 125

Port-channel: Po1 (Primary Aggregator)

------------

Age of the Port-channel = 00d:01h:46m:08s
Logical slot/port = 14/1 Number of ports = 3
Port state = Port-channel Ag-Inuse
Protocol = LACP

Ports in the Port-channel:

Index Load Port EC state No of bits
------+------+------+------------------+-----------
2 49 Gi3/1 Active 3
0 92 Gi3/2 Active 3
1 24 Gi3/3 Active 2

Time since last port bundled: 00d:01h:44m:15s Gi3/1

Displaying a Port in a link aggregation

Switch1#show interface GigabitEthernet 3/3 etherchannel
Port state = Up Mstr In-Bndl
Channel group = 1 Mode = Active Gcchange = -
Port-channel = Po1 GC = - Pseudo port-channel = Po1
Port index = 1 Load = 0xAA Protocol = LACP

Flags: S - Device is sending Slow LACPDUs F - Device is sending fast LACPDUs.
A - Device is in active mode. P - Device is in passive mode.

Local information:
LACP port Admin Oper Port Port
Port Flags State Priority Key Key Number State
Gi3/3 SA bndl 32768 0x1 0x1 0x303 0x3D

Partner's information:

Partner Partner Partner
Port System ID Port Number Age Flags
Gi3/3 00000,0030.6ef4.82380x5 19s SA

LACP Partner Partner Partner
Port Priority Oper Key Port State
0 0x384 0x3D

Displaying more LACP information

Switch1#show lacp 1 neighbor

Flags: S - Device is sending Slow LACPDUs F - Device is sending Fast LACPDUs
A - Device is in Active mode P - Device is in Passive mode

Channel group 1 neighbors

Partner's information:

Partner Partner Partner
Port System ID Port Number Age Flags
Gi3/1 00000,0030.6ef4.82380x6 17s SA

LACP Partner Partner Partner
Port Priority Oper Key Port State
0 0x384 0x3D

Partner's information:

Partner Partner Partner

Cisco 6509 switches

113

Содержание HP-UX 11i v3






























































































































Результаты поиска

Содержание HP-UX 11i v3

Отзывы:

Похожие инструкции для HP-UX 11i v3

Бренды по названию

Популярные бренды

HP HP-UX 11i v3, Руководство администратора

Результаты поиска

Содержание HP-UX 11i v3

Отзывы:

Похожие инструкции для HP-UX 11i v3

Бренды по названию

Популярные бренды