HP HP-UX 11i v3 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 125

background image

D VLANs over APA using HP Procurve switches

This appendix describes how to create VLANs over trunks and ports on an HP Procurve switch.
For more information about creating VLANs on HP Procurve switches, see Procurve, Series 6400cl
Switches, Series 5300xl Switches, Series 3400cl Switches, Advanced Traffic Management Guide at:

ftp://ftp.hp.com/pub/networking/software/6400-5300-3400-AdvTrafficMgmt-Oct2005-59906051.pdf

Configuring VLANs over link aggregates

Figure D-1 (page 105)

shows a configuration with a VLAN with ID 333 over

lan900

using ports

lan3

and

lan4

, with

lan3

and

lan4

connected to ports F23 and F24 on the switch, respectively.

Figure D-1 VLAN over a Link Aggregate

hp Pr oC ur ve
Sw it ch 8000

lan3 and lan4
form lan900

Power

Run

Attn.

Fault

Remote

Switch1

lan3

lan4

F23

F24

F23,24 form Trk3

To configure the VLAN on the switch, complete the following steps:
1.

Create the trunk on the switch side. Enter:

HP ProCurve Switch 5308xl#
HP ProCurve Switch 5308xl# configure
HP ProCurve Switch 5308xl(config)# trunk F23,F24 Trk3 trunk
HP ProCurve Switch 5308xl(config)# exit

F23

and

F24

are configured to be a MANUAL trunk at trunk name

Trk3

.

2.

Create the VLAN with ID 333 (

vlan_333

). Enter:

HP ProCurve Switch 5308xl#
HP ProCurve Switch 5308xl# configure
HP ProCurve Switch 5308xl(config)# vlan 333 name vlan_333
HP ProCurve Switch 5308xl(config)# exit

3.

Tag the trunk

Trk3

with the VLAN IDs to be used, in this case the ID is 333. Enter:

HP ProCurve Switch 5308xl(config)# vlan 333 tagged Trk3
HP ProCurve Switch 5308xl(config)# exit

Configuring VLANs over link aggregates

105

«
...
103
104
105
106
107
...
»

Содержание HP-UX 11i v3






























































































































Отзывы:

Нет отзывов

Похожие инструкции для HP-UX 11i v3

Бренд: NetComm Страницы: 6

Бренд: Saramonic Страницы: 2

Бренд: Targus Страницы: 8

Бренд: Cablematic Страницы: 19

Бренд: Ovislink Страницы: 13

Бренд: Ralink Страницы: 36

Бренд: Devolo Страницы: 22

Бренд: Tripp Lite Страницы: 25

AirLancer Extender SA-5L

Бренд: Lancom Страницы: 2

Powerline 1300 AV2 Adapter

Бренд: TRENDnet Страницы: 26

Бренд: Hama Страницы: 20

10/100/1000 Base-TX Ethernet PCI-X Adapter

Бренд: IBM Страницы: 32

Бренд: Nokia Страницы: 14

Бренд: Nokia Страницы: 23

Бренд: Nokia Страницы: 124

Бренд: Alpine Страницы: 44

Бренд: Sony Страницы: 2

BRAVIA KDL-60EX701

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды