HP F5000 Скачать руководство пользователя

Страница: 49 / 99

Hardware management and maintenance

This chapter includes these sections:

•

Displaying hardware information of the firewall

•

Solving system faults

•

Saving the current configuration of the firewall

•

Rebooting a module or the firewall

NOTE:

The output depends on your firewall model. For more information about the commands used in this
chapter, see the corresponding command references.

Displaying hardware information of the firewall

Displaying the software and hardware version information of
the firewall

Use the

display version

command to display software and hardware version information of the firewall.

The output includes the following information: the current software version and hardware version, firewall
operating time, type and operating time of each main processing unit (MPU) and interface module. The

output of this command depends on your firewall model.

<Sysname> display version

HP Comware Platform Software

Comware Software, Version 5.20, Release 3206P18

HP F5000 uptime is 0 week, 0 day, 0 hour, 3 minutes

2048M bytes DDR2 SDRAM Memory

4M bytes Flash Memory

247M bytes CF0 Card

MPUA PCB Version:Ver.B

SWBA PCB Version:Ver.A

MPUA Basic Logic Version: 3.0

MPUA Extend Logic Version: 1.0

SWBA Logic Version: 1.0

MPUA LX30T FPGA Version: 5.05

Basic BootWare Version: 1.07

Extend BootWare Version: 1.09

[FIXED PORT] CON (Hardware)Ver.B, (Driver)1.0, (Cpld)3.0

[FIXED PORT] AUX (Hardware)Ver.B, (Driver)1.0, (Cpld)3.0

[FIXED PORT] M-GE0/0 (Hardware)Ver.B, (Driver)1.0, (Cpld)3.0

[FIXED PORT] H-GE0/1 (Hardware)Ver.B, (Driver)1.0, (Cpld)3.0

Содержание F5000




































































































Результаты поиска

Содержание F5000

Отзывы:

Похожие инструкции для F5000

Бренды по названию

Популярные бренды

HP F5000, Руководство по установке

Результаты поиска

Содержание F5000

Отзывы:

Похожие инструкции для F5000

Бренды по названию

Популярные бренды