HP F5000 Скачать руководство пользователя

Страница: 12 / 99

Preparing for installation

This chapter includes these sections:

•

Safety recommendations

•

Examining the installation site

•

Installation tools

•

Accessories supplied by the firewall

•

Checklist before installation

Safety recommendations

Safety symbols

When reading this document, note the following symbols:

WARNING

means an alert that calls attention to important information that if not understood or

followed can result in personal injury.

CAUTION

means an alert that calls attention to important information that if not understood or

followed can result in data loss, data corruption, or damage to hardware or software.

General safety recommendations

•

Keep the chassis and installation tools away from walk areas.

•

Make sure that the ground is dry and flat and anti-slip measures are in place.

•

Unplug all the external cables (including power cords) before moving the chassis.

Safety with electricity

•

Locate the emergency power-off switch in the room before installation. Shut the power off at once in
case accident occurs.

•

Make sure that the firewall has been correctly grounded.

•

Do not open or close the chassis cover when the firewall is powered on.

•

Use an uninterrupted power supply (UPS).

•

If there are two power inputs, disconnect the two power inputs to power off the firewall.

•

Do not work alone when the firewall has power.

•

Always check that the power has been disconnected.

Safety with laser

•

Do not stare into the optical port or fiber connector because the laser light emitted from the optical
fiber may hurt your eyes.

•

Install a dust plug on the transceiver module to avoid damage to the transceiver module.

Содержание F5000




































































































Результаты поиска

Содержание F5000

Отзывы:

Похожие инструкции для F5000

Бренды по названию

Популярные бренды

HP F5000, Руководство по установке

Результаты поиска

Содержание F5000

Отзывы:

Похожие инструкции для F5000

Бренды по названию

Популярные бренды