HP Compaq SP750 Скачать руководство пользователя

Страница: 46 / 132

Removal and Replacement Procedures

4-5

Side Access Panel

CAUTION:

Do not operate the workstation with the side access panel removed. The panel is an

integral part of the cooling system; removing it while the system is running may adversely
affect data integrity.

To remove the side access panel:

Perform the steps in the “Service Preparations” section in this chapter, then place the
workstation on its side.

CAUTION:

Before removing the side access panel, ensure that the workstation is turned off, all

cables are disconnected from the back of the workstation, and the power cord is disconnected
from the grounded AC outlet.

Loosen the four rear panel thumbscrews and slide off the access panel.

Figure 4-3. Loosening the thumbscrews and removing the side access panel

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the internal system

components to cool before touching them.

WARNING:

When replacing the side access panel, be sure to tighten all four thumbscrews.

To replace the side access panel, reverse the above procedure.

Содержание Compaq SP750





































































































































Результаты поиска

Содержание Compaq SP750

Отзывы:

Похожие инструкции для Compaq SP750

Бренды по названию

Популярные бренды

HP Compaq SP750, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Compaq SP750

Отзывы:

Похожие инструкции для Compaq SP750

Бренды по названию

Популярные бренды