HP Compaq SP750 Скачать руководство пользователя

Страница: 45 / 132

4-4

Compaq Professional Workstation SP750 Maintenance and Service Guide

Workstation Feet

NOTE:

Not all procedures in this chapter require the removal of the workstation feet. Be sure to

thoroughly read each removal and replacement procedure before attempting to access any internal
components.

To remove the workstation feet:

Perform the steps in the “Service Preparations” section in this chapter, then place the
workstation on its side.

CAUTION:

Before removing the side access panel, ensure that the workstation is turned off, all

cables are disconnected from the back of the workstation, and the power cord is disconnected
from the grounded AC outlet.

Remove the screws that secure the feet.

Remove the workstation feet.

Figure 4-2. Removing the workstation feet

To replace the feet, reverse the above procedure.

Содержание Compaq SP750





































































































































Результаты поиска

Содержание Compaq SP750

Отзывы:

Похожие инструкции для Compaq SP750

Бренды по названию

Популярные бренды

HP Compaq SP750, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Compaq SP750

Отзывы:

Похожие инструкции для Compaq SP750

Бренды по названию

Популярные бренды