HP Compaq dc5100 Series Скачать руководство пользователя страница 46

Страница: 46 / 230

3–16

376220-001

Service Reference Guide, dc5100

Desktop Management

Save Master Boot Record

Saves a backup copy of the Master Boot Record of the current
bootable disk.
Only appears if MBR Security is enabled.

Restore Master Boot Record

Restores the backup Master Boot Record to the current
bootable disk.

✎

Only appears if all of the following conditions are true:

• MBR Security is enabled.
• A backup copy of the MBR has been previously saved.
• The current bootable disk is the same disk from which the

backup copy of the MBR was saved.

CAUTION:

Restoring a previously saved MBR after a disk

utility or the operating system has modified the MBR may

cause the data on the disk to become inaccessible. Only

restore a previously saved MBR if you are confident that the

current bootable disk’s MBR has been corrupted or infected

with a virus.

Computer Setup Utilities (F10) Security Features

(Continued)

Feature

Description

✎

For more information about Computer Setup, see the

Computer Setup (F10) Utility Guide

Support for security features may vary depending on your specific computer configuration.

Mechanical Security Features

Feature

Purpose

How It Is Established

Memory Change Alerts

Detects when memory modules
have been added, moved, or
removed; notifies user and
system administrator.

For information on enabling
Memory Change Alerts, refer
to the online

Desktop

Management Guide

on the

Documentation CD.

Cable Lock Provision

Inhibits access to the interior of
the computer to prevent
unwanted configuration
changes or component
removal. Can also be used to
secure the computer to a fixed
object to prevent theft.

Install a cable lock to secure
the computer to a fixed
object.

Security Loop Provision

Inhibits access to the interior of
the computer to prevent
unwanted configuration
changes or component
removal.

Install a lock in the security
loop to prevent unwanted
configuration changes or
component removal.

Содержание Compaq dc5100 Series







































































































































































































































Результаты поиска

Содержание Compaq dc5100 Series

Отзывы:

Похожие инструкции для Compaq dc5100 Series

Бренды по названию

Популярные бренды

HP Compaq dc5100 Series, Руководство по обслуживанию и справочник

Результаты поиска

Содержание Compaq dc5100 Series

Отзывы:

Похожие инструкции для Compaq dc5100 Series

Бренды по названию

Популярные бренды