HP Compaq dc5000 MT Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 180

background image

Service Reference Guide, dc5000

360201-002

C–3

POST Error Messages

214-DIMM
Configuration Warning

Populated DIMM
Configuration is
unbalanced.

2 DIMMS - For maximum performance,
place both DIMMs in the two BLACK
DIMM slots.
4 DIMMS - For maximum performance,
swap one DIMM in a BLUE slot with one
in a BLACK slot.

301-Keyboard Error

Keyboard failure.

Reconnect keyboard with computer
turned off.
Check connector for bent or missing
pins.
Ensure that none of the keys are
depressed.
Replace keyboard.

303-Keyboard
Controller Error

I/O board keyboard
controller.

Reconnect keyboard with computer
turned off.
Replace the system board.

304-Keyboard or
System Unit Error

Keyboard failure.

Reconnect the keyboard with computer
turned off.
Ensure that none of the keys are
depressed.
Replace keyboard.
Replace system board.

401-Parallel Port 1
Address Assignment
Conflict

IRQ address conflicts with
another device.

Reset the IRQ.

402-Parallel Port 2
Address Assignment
Conflict

IRQ address conflicts with
another device.

Reset the IRQ.

403-Parallel Port 3
Address Assignment
Conflict

IRQ address conflicts with
another device.

Reset the IRQ.

404-Parallel Port
Address Conflict
Detected

Both external and internal
ports are assigned to
parallel port X.

Remove any parallel expansion cards.
Clear CMOS.
Reconfigure card resources and/or run
Computer Setup (F10 Setup).

410-Audio Interrupt
Conflict

IRQ address conflicts with
another device.

Reset the IRQ.

411-Network Interface
Card Interrupt Conflict

IRQ address conflicts with
another device.

Reset the IRQ.

417-Network Interface
card Failure

Failure to read MAC
address information from
NIC.

Unplug AC power cord, wait 5 seconds,
then reboot unit.

POST Error Messages

Screen Message

Probable Cause

Recommended Action

«
...
133
134
135
136
137
...
»

Содержание Compaq dc5000 MT





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq dc5000 MT

Personal Computer

Бренд: IBM Страницы: 64

Бренд: IBM Страницы: 158

dc5800 - Microtower PC

Бренд: Compaq Страницы: 69

Бренд: ZIEHL-ABEGG Страницы: 84

Бренд: Aaeon Страницы: 43

Height Adjustable Standing Desk 4-Leg

Бренд: Uplift Desk Страницы: 16

Бренд: Asus Страницы: 50

Бренд: Asus Страницы: 26

Бренд: Asus Страницы: 22

Бренд: Asus Страницы: 26

Бренд: Asus Страницы: 16

Бренд: Asus Страницы: 2

Бренд: Asus Страницы: 98

Бренд: Asus Страницы: 70

Бренд: Asus Страницы: 70

Бренд: Asus Страницы: 80

Бренд: Asus Страницы: 70

Бренд: Asus Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды